If you’re experiencing issues with the back camera on your iPhone 6s, such as blurry photos or a cracked lens, you may need to remove and replace the camera lens. This is a relatively simple procedure that can be done at home with the right tools and a little bit of patience.
Before you begin, it’s important to note that opening your iPhone may void any existing warranties. If your iPhone is still under warranty or if you’re unsure about performing the repair yourself, it’s best to take it to an authorized service center or contact Apple support for assistance.
If you’re confident in your technical skills and are ready to proceed, here are the steps to remove the back camera lens on your iPhone 6s:
Step-by-step guide to remove the back camera lens on iPhone 6s
Having trouble with your iPhone 6s back camera lens? Don’t worry, we are here to help! Follow these steps to remove the back camera lens on your iPhone 6s without damaging the device:
Step 1: Gather the necessary tools
Before you start, make sure you have the following tools:
- Pentalobe screwdriver
- Small suction cup
- Plastic spudger or a thin and flat plastic tool
- Tweezers
Step 2: Power off your iPhone
Before working on your device, turn it off to avoid any potential accidents or damage.
Step 3: Remove the screws
Use the Pentalobe screwdriver to remove the two screws located at the bottom of your iPhone. Set the screws aside in a safe place.
Step 4: Use the suction cup
Place the suction cup above the Home button and gently pull upwards to create a small opening between the screen and the device’s body. Be careful not to apply too much pressure, as it may damage the device.
Step 5: Insert the plastic spudger
Insert the plastic spudger or a thin and flat plastic tool into the opening you created with the suction cup. Gently move the tool around the edges to separate the screen from the device’s body. Be cautious and take your time to avoid damaging any internal components.
Step 6: Lift the screen
Once the screen is separated from the device’s body, carefully lift it up from the bottom edge using the plastic spudger or your fingers. Be gentle and keep in mind that there are delicate ribbons attaching the screen to the device.
Step 7: Locate the back camera lens
With the screen lifted, you will see the back camera lens located at the top right corner of the device. It is a small circular component attached to the back of the screen.
Step 8: Remove the camera lens
Use the tweezers to carefully detach the camera lens from the back of the screen. Pull it gently upwards and ensure not to damage any surrounding components. If needed, you can use the plastic spudger to help with the removal process.
Step 9: Replace the camera lens
If you have a new camera lens, carefully attach it to the back of the screen using the tweezers. Ensure it is aligned correctly before applying any pressure.
Step 10: Reassemble your iPhone
Reverse the steps above to reattach the screen, screw in the two Pentalobe screws, and power on your iPhone. Test the back camera to ensure it is functioning properly.
By following these steps, you should be able to remove the back camera lens on your iPhone 6s. Remember to take your time and be gentle throughout the process to avoid any damage to your device.
Tools required for removing the back camera lens
Before attempting to remove the back camera lens on your iPhone 6s, make sure you have the following tools:
1. Phillips screwdriver:
You will need a Phillips screwdriver (size #000) to remove the screws that secure the back camera lens in place. This type of screwdriver has a cross-shaped tip which fits into the screws.
2. Plastic pry tool:
A plastic pry tool is essential for safely separating the back camera lens from the iPhone body. This tool helps you avoid damaging the delicate components or scratching the surface of your iPhone during the removal process.
3. Tweezers:
Tweezers are useful for handling small screws or other tiny components during the removal and reassembly process. They provide better control and precision when working with small parts.
4. Adhesive strips:
Adhesive strips are necessary for securing the new back camera lens in place after the old one has been removed. These adhesive strips help ensure a tight and secure fit, preventing any potential movement or damage to the camera lens.
It is important to have these tools readily available and to exercise caution while removing the back camera lens to avoid any accidental damage to your iPhone 6s.
Preparation steps before removing the back camera lens
Before removing the back camera lens on your iPhone 6s, it’s important to follow a few preparation steps to ensure the process goes smoothly and without any damage.
1. Gather the necessary tools
It’s essential to have the right tools before attempting to remove the back camera lens. You will need a small screwdriver set, a plastic pry tool, and a suction cup. Having these tools ready will make the process much easier.
2. Power off your iPhone
Before you begin disassembling your iPhone, make sure it is powered off to avoid any accidental damage or electrical issues.
3. Remove the SIM card tray
Using the SIM card removal tool or a small paperclip, open the SIM card tray located on the side of your iPhone. This step will allow you to safely access the necessary components for removing the back camera lens.
4. Heat the back of your iPhone
Using a hairdryer or a heat gun set to low heat, gently warm the back of your iPhone. The heat will help soften the adhesive securing the back camera lens, making it easier to remove.
5. Apply suction cup
Place the suction cup firmly on the back of your iPhone, just above the home button. Make sure it is securely attached, as it will provide leverage when removing the back camera lens.
6. Gently lift the back panel
Once the suction cup is securely attached, gently pull up on the cup to lift the back panel of your iPhone. Be careful not to pull too hard or apply excessive force, as this may cause damage to the device. Slowly move your fingers along the edges to continue loosening the adhesive.
7. Disconnect the camera flex cables
Once the back panel is lifted, you will need to disconnect the camera flex cables that connect the back camera lens to the motherboard. Carefully pry them up using the plastic pry tool, making sure to not damage any of the delicate components.
Following these preparation steps will help ensure a successful removal of the back camera lens on your iPhone 6s. Remember to proceed with caution and take your time to avoid any unnecessary damage to your device.
How to remove the screws holding the back camera lens in place
Removing the screws that hold the back camera lens in place on your iPhone 6s requires some precision and the right tools. Here’s a step-by-step guide to help you:
- Start by powering off your iPhone and disconnecting any cables connected to it.
- Get a high-quality Phillips #000 screwdriver. This small-sized screwdriver is essential for removing the screws holding the camera lens.
- Flip your iPhone 6s upside down so that the back is facing you.
- Locate the two screws on either side of the camera lens. These screws secure the lens in position.
- Use the Phillips #000 screwdriver to carefully unscrew these two screws. Make sure you apply firm but gentle pressure to avoid damaging the screws or the surrounding components.
- Once you feel the screws become loose, use your fingers or a pair of tweezers to completely remove them from the device.
- Set the screws aside in a secure place to avoid losing them.
With the screws removed, the back camera lens of your iPhone 6s should be ready to come off. Be cautious while removing the lens to prevent accidental damage.
Removing the adhesive tape securing the back camera lens
Before removing the back camera lens of your iPhone 6s, it is important to remove the adhesive tape that secures the lens in place. The adhesive tape helps to keep the lens securely attached to the device, and removing it properly can prevent any damage or misalignment of the lens.
Follow the steps below to remove the adhesive tape:
-
Power off your iPhone 6s and disconnect any cables.
-
Use a small Phillips screwdriver to remove the two screws located on each side of the charging port.
-
Insert a suction cup near the home button and gently lift the display assembly. Be careful not to pull too hard as it may damage the display cables.
-
Use a plastic opening tool or a spudger to carefully separate the display assembly from the rear case. Start from the bottom and slowly work your way around the sides.
-
Once the display assembly is separated from the rear case, carefully remove it and set it aside.
-
Locate the back camera lens and the adhesive tape that secures it.
-
Gently peel off the adhesive tape using a pair of tweezers or a plastic opening tool. Start from one corner and slowly work your way around until the tape is completely removed.
-
Once the adhesive tape is removed, you can safely detach the back camera lens from the device.
Remember to handle the back camera lens with care to avoid any smudges or scratches. You can now proceed with replacing or repairing the lens as needed.
Carefully removing the back camera lens from the iPhone 6s
Removing the back camera lens from an iPhone 6s requires caution and precision to avoid causing damage. Here are the steps to safely remove the camera lens:
Step 1: Gather the necessary tools
Before starting, make sure to gather the tools needed for the procedure. You will need a small suction cup, a flathead screwdriver, a pentalobe screwdriver, a spudger, and a pair of tweezers.
Step 2: Power off the iPhone
Before attempting any repairs, it is essential to power off the iPhone to prevent any potential electrical damage or accidents.
Step 3: Remove the outer screws
Using the pentalobe screwdriver, carefully remove the two small screws on the bottom edge of the iPhone near the charging port.
Step 4: Use suction cup to lift the display
Place the suction cup on the lower half of the iPhone’s screen, just above the home button. Apply gentle pressure and lift the display assembly slightly to create a small gap between the screen and the rear case of the iPhone.
Step 5: Insert the spudger
Slide the spudger into the gap created by the suction cup. Carefully move the spudger along the sides of the iPhone to separate the adhesive and release the clips holding the display assembly in place.
Step 6: Lift the display assembly
Gently lift the display assembly from the rear case, making sure to open it like a book and support it with something to prevent straining the display cables.
Step 7: Locate and remove the back camera lens
Locate the back camera lens on the rear side of the iPhone. It is positioned near the top left corner of the inner housing. Use the pair of tweezers to carefully lift and remove the camera lens.
Step 8: Replace the lens or clean it
If you are planning to replace the lens, make sure to do so with a compatible replacement part. If you are cleaning the lens, gently wipe it using a microfiber cloth or a lens cleaning solution.
Step 9: Reassemble the iPhone
Once the camera lens has been removed or cleaned, carefully reassemble the iPhone by following the steps in reverse order. Make sure all the connectors are securely seated and the adhesive is properly aligned before pressing the display assembly back onto the rear case.
Following these steps will allow you to remove the back camera lens from your iPhone 6s safely. Remember to exercise caution and take your time to avoid any unnecessary damage.
Cleaning and replacing the back camera lens on iPhone 6s
One of the important components of the iPhone 6s is its back camera lens. Over time, this lens may accumulate dust, smudges, or scratches that can affect the quality of the photos or videos taken. To ensure optimal performance, it is important to clean or replace the back camera lens when necessary. Here are the steps to clean or replace the back camera lens on your iPhone 6s:
Cleaning the back camera lens:
- Turn off your iPhone 6s and remove the case, if any.
- Gently wipe the back camera lens using a microfiber cloth to remove any visible dust or smudges. Be careful not to apply excessive pressure.
- If there are stubborn stains or fingerprints on the lens, dampen the microfiber cloth slightly with lens cleaning solution or isopropyl alcohol. Again, be gentle when wiping the lens to avoid scratching.
- After cleaning, use a dry part of the cloth to wipe away any moisture residue.
Replacing the back camera lens:
- If the back camera lens is scratched or damaged beyond cleaning, you may need to replace it.
- Purchase a replacement back camera lens from a trusted supplier or Apple Store.
- Power off your iPhone 6s and remove the case, if any.
- Use a small pentalobe screwdriver to unscrew the two screws located near the side of the lightning connector.
- Gently lift the display assembly using a suction cup or a pry tool to create a small gap.
- While holding the display assembly up, remove the screws securing the metal plate covering the connectors near the top of the device.
- Disconnect the connectors underneath the metal plate carefully.
- Remove the screws securing the metal plate covering the back camera lens.
- Gently lift the metal plate and disconnect the connector attached to the back camera lens.
- Replace the old back camera lens with the new one.
- Reassemble your iPhone 6s by following the steps in reverse order.
By cleaning or replacing the back camera lens on your iPhone 6s, you can ensure optimal performance and capture clear and sharp photos or videos. Remember to handle the camera lens with care and take necessary precautions to avoid any damages during the process.
FAQ
Can I remove the back camera lens on my iPhone 6s?
Yes, you can remove the back camera lens on your iPhone 6s. However, it is important to proceed with caution and follow the proper steps to avoid damaging the lens or other components of your device.
What tools do I need to remove the back camera lens on my iPhone 6s?
To remove the back camera lens on your iPhone 6s, you will need a few tools including a small Phillips screwdriver, a plastic opening tool or a suction cup, and a pair of tweezers. These tools will help you safely remove the lens without causing any damage.
