iPhone 7 Plus is renowned for its stunning camera capabilities, allowing users to capture high-quality photos and videos. However, accidents can happen, and the back camera lens may become scratched or cracked, affecting the camera’s performance. Fortunately, replacing the back camera lens on the iPhone 7 Plus is a relatively straightforward process that you can do at home.
Before you begin: Make sure you have a replacement lens specifically designed for the iPhone 7 Plus. You can purchase one from reputable online retailers or visit a local electronics store. Additionally, gather the necessary tools, which typically include a small Phillips screwdriver, a pair of tweezers, and a plastic opening tool.
Step 1: Power off your iPhone 7 Plus and lay it on a clean, flat surface. Use the small Phillips screwdriver to remove the two screws located at the bottom of the phone, on either side of the charging port.
Step 2: Gently insert the plastic opening tool between the display assembly and the rear case, starting from the bottom right corner. Slowly and carefully, slide the opening tool along the right edge of the phone, separating the adhesive and lifting the display assembly.
Step 3: Once the display assembly is partially lifted, use the opening tool to carefully lift the bottom left corner as well. Be cautious not to apply too much force, as this may damage the ribbon cables connecting the display assembly to the motherboard.
Step 4: With the display assembly lifted, locate the metal shield covering the camera module. Remove the screws securing the shield and gently lift it away. You will now have access to the back camera lens.
Step 5: Use the tweezers to carefully remove the damaged back camera lens. Take note of the positioning of the lens, as the replacement lens should be installed in the same way.
Step 6: Take the new camera lens and insert it into the designated slot, ensuring it is aligned correctly. Press it down gently to secure it in place.
Step 7: Reassemble the metal shield and secure it with the screws. Carefully lower the display assembly back onto the rear case, starting with the top part first. Press down along the edges to ensure the adhesive is properly sealed.
Step 8: Finally, insert and tighten the two screws at the bottom of the phone to secure the display assembly. Power on your iPhone 7 Plus and test the back camera to ensure it is working correctly.
Replacing the back camera lens on your iPhone 7 Plus can save you the cost and hassle of getting it professionally repaired. However, if you are not confident in your skills or encounter any difficulties during the process, it is always recommended to seek assistance from a certified technician to avoid further damage to your device.
Step-by-step guide to replacing the iPhone 7 Plus back camera lens
If you are experiencing issues with the camera lens on your iPhone 7 Plus, replacing it can be a cost-effective solution. Here is a step-by-step guide to help you replace the back camera lens on your iPhone 7 Plus:
- Make sure you have the right tools for the job. You will need a set of small screwdrivers, a plastic pry tool, a suction cup, and replacement camera lens.
- Power off your iPhone and remove the SIM card tray using a SIM card eject tool.
- Next, remove the two bottom screws located on either side of the charging port using a pentalobe screwdriver.
- Place the suction cup on the screen, near the home button, and gently pull up to create a small gap.
- Insert the plastic pry tool into the gap and carefully slide it along the edge of the phone to remove the display assembly.
- Once the display assembly is lifted, disconnect the cables connecting the display to the logic board by using a small screwdriver or spudger.
- Remove the screws securing the metal bracket covering the rear camera connectors.
- Disconnect the rear camera connectors and carefully remove the bracket.
- Gently remove the damaged camera lens by lifting it up from the adhesive.
- Clean the area around the camera lens and remove any traces of adhesive left behind.
- Take the replacement camera lens and carefully align it with the opening in the phone.
- Press down firmly to secure the adhesive and ensure proper alignment.
- Reassemble the rear camera connectors, metal bracket, and cables in the reverse order.
- Place the display assembly back in its original position and press down to secure it.
- Insert the two bottom screws back into the charging port.
- Finally, insert the SIM card tray and power on your iPhone to test the new camera lens.
By following these step-by-step instructions, you can easily replace the back camera lens on your iPhone 7 Plus and restore its functionality. Remember to exercise caution and work in a well-lit and clean environment to avoid any damage to your device.
Gather the necessary tools
Before you begin replacing the back camera lens on your iPhone 7 Plus, make sure you have all the necessary tools for the job. Having the correct tools will make the process much easier and reduce the risk of damaging your device. Here is a list of tools you will need:
| Tools | Description |
|---|---|
| Small Phillips screwdriver | Used to remove the screws holding the back panel in place. |
| Plastic opening tools | Used to pry open the back panel and disconnect the cables. |
| Tweezers | Used to handle small parts and screws. |
| Suction cup | Used to lift the back panel off the device. |
| Adhesive strips | Used to secure the new camera lens in place. |
Make sure to gather these tools before starting the repair process. Having them easily accessible will save you time and frustration during the replacement.
Power off the iPhone 7 Plus
Before replacing the back camera lens on your iPhone 7 Plus, you should first power off the device to avoid any accidental damage. Here are the steps to power off your iPhone 7 Plus:
- Press and hold the side button (also known as the power button) located on the right side of the device.
- Wait for the “Slide to power off” slider to appear on the screen.
- Drag the slider from left to right to power off your iPhone 7 Plus.
Once your device is powered off, you can proceed to the next steps of replacing the back camera lens.
Remove the rear panel
Before you begin, make sure your iPhone is powered off. This is important for your safety and to prevent any damage to the device.
1. Locate the two pentalobe screws at the bottom edge of the iPhone.
2. Use a pentalobe screwdriver to unscrew these two screws. They are small and easy to lose, so be careful.
3. Place a suction cup near the home button and gently pull up. This will create a small gap between the rear panel and the rest of the device.
4. Insert a plastic opening tool into the gap and slowly slide it along the edge of the iPhone. This will help loosen the adhesive holding the rear panel in place.
5. Continue sliding the plastic opening tool around the edge of the iPhone, separating the adhesive as you go. Be gentle and take your time to avoid damaging the rear panel.
6. Once the adhesive is loosened around the entire rear panel, gently lift it up from the bottom of the device.
7. Be careful not to tear any of the cables attached to the rear panel. If you encounter resistance, double-check for any remaining adhesive and gently separate it before continuing.
8. With the rear panel removed, you now have access to the internal components of your iPhone 7 Plus, including the back camera lens.
Make sure to keep track of all screws and components you remove, as you will need them for reassembly.
Access the back camera lens
To replace the back camera lens on your iPhone 7 Plus, you will first need to access it. Follow these steps to gain access to the lens:
-
Power off your iPhone completely before beginning the replacement process. This will ensure your safety and prevent any damage to the device.
-
Locate the two screws at the bottom of your iPhone. Use a pentalobe screwdriver to remove these screws.
-
Once the screws are removed, you can gently slide the back panel upwards to remove it from the device.
-
Take note of any adhesive that may be holding the panel in place and use a spudger or other pry tool to carefully release it.
-
With the back panel removed, you will now have access to the camera lens. Take caution when handling the lens to avoid any damage.
By following these steps, you will be able to access the back camera lens on your iPhone 7 Plus. Make sure to take your time and be gentle when handling the device to avoid any further damage.
Replace the damaged lens
If you have a damaged back camera lens on your iPhone 7 Plus, you can easily replace it following these steps:
Step 1: Gather the necessary tools
Before you begin, make sure you have the following tools:
- Replacement camera lens
- Small Phillips screwdriver
- Flathead screwdriver
- Spudger tool
- Tweezers
- Adhesive
- Heat gun or hairdryer
Step 2: Power off and remove the back panel
Power off your iPhone 7 Plus and remove the two screws located near the Lightning port. Use a heat gun or hairdryer to heat the back panel, then use a suction cup and the spudger tool to slowly pry off the panel.
Step 3: Disconnect the battery
Using your Phillips screwdriver, remove the shield covering the battery connector. Disconnect the battery by gently lifting the connector with the spudger tool, being careful not to damage any of the nearby cables.
Step 4: Remove the camera module
Locate the camera module at the top of the back panel. Use the flathead screwdriver to remove the screws securing it in place. Carefully disconnect the ribbon cables attached to the module with the spudger tool. Remove the old camera module.
Step 5: Install the new camera lens
Take your new camera lens and align it with the camera module. Carefully attach the ribbon cables to the module using the tweezers, making sure they are securely connected. Place the screws back in their original positions to secure the camera module.
Step 6: Reassemble your iPhone
Reconnect the battery by gently pressing down on the connector. Replace the shield covering the battery connector with the Phillips screwdriver. Carefully align the back panel with the phone and press it down until it snaps into place. Replace the two screws near the Lightning port.
Once you have completed these steps, your iPhone 7 Plus should have a new camera lens installed and be ready to use.
Reassemble the iPhone 7 Plus
Once you have successfully replaced the back camera lens on your iPhone 7 Plus, it is time to reassemble the device. Follow the steps below to ensure everything is put back together correctly.
Step 1: Position the Back Cover
Carefully position the back cover onto the back of the iPhone 7 Plus, ensuring that the camera lens aligns with the appropriate opening. Gently press down to attach the cover securely.
Step 2: Secure the Screws
Using the appropriate screwdriver, secure the screws back into their original positions. Be cautious not to overtighten the screws, as this can damage the device.
Step 3: Reattach the SIM Card Tray
Insert the SIM card tray back into its slot on the side of the iPhone 7 Plus. Ensure that it is inserted correctly and flush with the device’s frame.
Step 4: Place the Screen
Securely place the screen onto the front of the iPhone 7 Plus. Gently press down around the edges to ensure it is properly attached.
Step 5: Test the Camera
Power on your iPhone 7 Plus and test the rear camera to ensure it is functioning correctly. Open the camera app, take a few test photos, and check for any issues.
By following these steps, you should be able to successfully reassemble your iPhone 7 Plus after replacing the back camera lens. If you encounter any difficulties or issues, it is recommended to seek professional assistance or consult the Apple support website for additional guidance.
FAQ
What should I do if the back camera lens on my iPhone 7 Plus is cracked?
If the back camera lens on your iPhone 7 Plus is cracked, you will need to replace it. You can either take it to a professional repair service or replace it yourself if you are confident in your technical skills.
Can I replace the iPhone 7 Plus back camera lens myself?
Yes, you can replace the iPhone 7 Plus back camera lens yourself if you have the necessary tools and knowledge. However, it is recommended to proceed with caution as any mistakes during the procedure can permanently damage your device.
What tools will I need to replace the back camera lens on my iPhone 7 Plus?
To replace the back camera lens on your iPhone 7 Plus, you will need a small Phillips screwdriver, a suction cup, a pry tool, tweezers, and a replacement camera lens. These tools will help you open the device, remove the old lens, and install the new one.
